Something that can definitely assistance your experience is to have the proper size shocks, which Incidentally the DJM Calmax shocks are created specifically for their lowering kits! So the best choice might be the DJM shocks. Send out us a picture within your Ram when your done!
.and #3 ik the truck sits manufacturing unit taller from the back again and when I put in the 2 inch blocks it seemed essentially leveled which I like but I want it reduce ..would the 3/4 fall hold it leveled? definitely I just wanna maintain the nose decrease as opposed to again, degree would be best but as long as it doesn’t seem like my truck has a complete load all the time
24″s are significant and costly so watch out specifically in the front! Very good luck and send out some photos!!
haha. Unfortunately this truck can be an eight lug, if it ended up a 6 lug I'd personally already have gotten this hammered out. I assume back to your drafting board!! I actually don’t want to buy a kit and it not perform then be trapped with it! Many thanks for the assistance!!
Certainly the ball joints have zerk fittings, and although they're not the manufacturing facility substitution elements, These are parts you can find any any NAPA or tricky sections retail outlet! And no There exists not a shackle You should use to add to the two″ blocks, it is possible to however modify out the 2″ blocks for three″ or 4″ blocks to get the stance your on the lookout for!
I'm away from city at this time and am owning trouble attending to the online world. But you can go ahead and mail to [email protected] and I really should manage to get them! Many thanks for the photos!!
Looks like key diegrinder operate and pulling the UCA’s. I believed all this stuff was to take care of manufacturing facility alignment?? No less than near would have been neat.
You happen to be right in regards to the Handle arms, they can bolt up the same as manufacturing unit. The challenge is definitely the rear and although I don’t know needless to say I doubt which the hanger shackle kit will “just bolt up†Very first attempt to determine when there is more than enough space to install a longer shackle about the rear of the leaf spring (ensure that it clears the gasoline filler neck), then test to check out if the hole sample around the manufacturing unit hanger appears like the outlet sample within the fall hangers.
Thanks for selecting DJM to lower your truck! You are accurate with regard to the shock figures, just use a pair of 1415’s within the front and a set of 2200’s in your rear. Concerning the bushings, the component number BK2555L can be a bushing substitution kit with the decreased control arms, that won’t perform for the swaybar.
Brink states: November 27, 2013 at 9:forty two pm Nicely wound up going Together with the 2″ lowers as well as your shocks all of the way around. Not fairly confident why my leaf broke, I used to be dumbfounded when my uncles shop stated it had been my leaf spring. I used to be pulling out of a parking lot, it had been raining saw a coworker so received on it to drift out of the lot an listened to a snap.
juan penaloza suggests: April 22, 2014 at 8:31 pm howdy djm i just installed your four/6 package on my 2000 silverado i have a few difficulties i did the install two weeks ago and actually much like the way it rides but i did recognize my steering wheel shakes a little this past weekend i had mew tires placed on it and received an alignment the dude that did the alignment explained he did his best but couldn't get it to specs very well the steering wheel shakes far more driving in the future then it did prior to the alignment and another issue is that the back again to the passenger side sits about one inch greater then the drivers side can i include a decreasing shackle to really make it glance even would that work thanks for almost any allow you to can provide
The reason the website only goes again to seventy three around the eight lug truck is the fact that’s as far back as We've got had an opportunity to work on! The front Calmax Command arms would most likely work but they have the disc brake ball joints in them so you would want to alter out the ball joints.
checking on reducing springs and some say the trip will likely be inventory or greater and some say the journey are going to be like Using in a logging truck then there was the shocks problem new good shocks are about 60% much less then 2in drop shocks soon after examining the spec uncovered the next stock shock Extended Duration:thirteen.
Also, I'm sure this one particular isn’t a tech question but, Click For More Did you know of the dependable shipping and delivery provider to get it above to me.